top of page

Can You Take a Wrapped or PPF-Covered Car Through a Car Wash?

Writer: Three Rivers Car Wash
Three Rivers Car Wash
8 minutes ago
6 min read

Yes, within the limits the filmmakers set, and a touchless wash is the option they favor. 3M's wrap care FAQ says, "Vinyl wraps can be run through car washes; however, touchless car washes are the best for graphic care," and Avery Dennison's cleaning bulletin says, "A brushless automatic car wash with just spray is acceptable."

 

Avery Dennison's bulletin also gives advice aimed at the car wash itself: "Skip the wax options at the car wash to avoid wax that contains petroleum distillates which can damage the wrap," and keep cleaning chemicals and detergents at a "pH balance between 5 and 9." The film makers also disagree on pressure: Avery says below 1200 psi, while 3M says below 2000 psi. This post covers what 3M, Avery Dennison and XPEL say about brush washes, wait times after install, pressure and nozzle limits, wax options and spot cleaning.


Three Rivers Car Wash - Featured Image

Can a Wrapped or PPF-Covered Car Go Through an Automatic Car Wash?

 

A vehicle wrap is a vinyl film applied over the paint to change its color or add graphics, and paint protection film, or PPF, is a film applied to shield the paint underneath. Both makers' warnings come back to the film's edges.

 

Here is what each maker says about automatic washes:

 

Film maker

What it says about automatic washes

3M (vinyl wraps)

Can go through car washes; "touchless car washes are the best for graphic care"

Avery Dennison (vinyl wraps)

"A brushless automatic car wash with just spray is acceptable"

XPEL (COLOR PPF)

"Do not use automatic tunnel car washes, this will severely scratch and damage the finish."

 

XPEL's tunnel wash warning is printed under its COLOR PPF line. Its care instructions for ULTIMATE PLUS, ULTIMATE FUSION and STEALTH films do not address automatic washes, so check with your installer for those.

 

3M also notes that "hand washing is the preferred cleaning method," with pressure washing allowed under conditions covered below.

 

Why Are Brush Washes a Risk for Film Edges?

 

Both wrap makers name the same problem. 3M says, "Brush car washes may cause dulling or scratching and can cause lifting around the edges of the graphics." Avery Dennison says an automated brush wash "is not recommended as the brushes may scratch the vinyl surface, catch and lift the edges of the vinyl wrap, reduce the gloss finish and/or create a failure point."

 

Edges come up again in both makers' pressure washing advice. For more on friction washes, see whether soft-touch washes can scratch clear coat or wraps.

 

How Long Should You Wait Before the First Wash?

 

The adhesive needs time to set. The makers give different waits:

 

Film

Wait before first wash

XPEL ULTIMATE PLUS, ULTIMATE FUSION, STEALTH

48 hours

XPEL COLOR PPF

72 hours

XPEL windshield film

At least 48 hours

Avery Dennison Supreme Wrap

48 hours

3M vinyl wraps

The first week

 

3M adds a cold weather note: "You may need to wait even longer if the weather is very cold." For a wrap installed in late fall in Western Pennsylvania, ask your installer how long to wait before the first salt-season wash.

 

What Pressure, Distance and Nozzle Do Film Makers Allow?

 

Each maker sets its own numbers:

 

Source

Pressure

Water temperature

Nozzle and distance

3M wraps

"below 2000 psi (14 MPa)"

"below 80 °C (180 °F)"

40 degree spray, "at least 1 foot (300 mm) away from and at 90 degrees to the graphic"

Avery Dennison wraps

"below 1200 psi"

"below 180˚F (80˚C)"

40 degree spray, "at least 12 inches away from the edges," perpendicular

XPEL COLOR PPF

Not stated

Not stated

"stay 3ft away from the paintwork"

XPEL windshield film

Not stated

Not stated

"at least 36 inches (1 meter) away," 40 degree nozzle

Polestar foil finish

"no more than 1200 psi(80 bar)"

No hotter than 60 °C (140 °F)

40 degree nozzle with tip guard, at least 30 cm (13 in.) straight on

 

Angle matters too. 3M says, "Don't hold the pressure washer at an angle to the wrap as it may lift the edges of the film," and XPEL says to avoid "a pressure washer or high-pressure water source near the edges of the film." Polestar, whose BST edition cars come with foil finish parts, says to "always use an angle greater than 60°" near foil edges.

 

Avery Dennison adds a caution. Its bulletin says a pressure washer "should only be used when all other cleaning methods have been used or tested and did not properly work," because it can cause "edge-lifting and face degradation."

 

Should You Pick the Wax Option on a Wrapped Car?

 

Not according to Avery Dennison, which says to skip the wax options at the car wash. 3M goes further and strongly recommends against wax or similar coatings on vehicle graphics.

 

The makers differ on wax applied by hand. Avery allows wax that "does not contain petroleum distillates or abrasive components" and says to test it in an inconspicuous area first, while 3M advises against wax on wraps altogether.

 

Matte and textured films need extra care:

 

  • 3M recommends no "abrasive polishes, cutting compounds or wax products on matte or textured films."

  • Avery Dennison says waterless wash products with wax "can fill in the texture and cause shiny spots."

  • XPEL says to seal its satin STEALTH film with XPEL Ceramic Boost "at least once every 6 months."

 

For ceramic or polish add-ons, the post on what a ceramic shine car wash is gives the same advice as the film makers: if your vehicle has wraps, check the manufacturer's care instructions before choosing any wash product.

 

What Should You Keep Off a Wrap Between Washes?

 

Some contaminants cannot wait for the next wash. Avery Dennison says spot cleaning of "bugs, bird droppings, tree sap and tar is required immediately after it appears, as it can stain and damage the PVC film," and adds, "This is also true of gasoline and other fuels." XPEL says not to let "bugs, bird residue, hard water spots" sit and dry on COLOR PPF.

 

For stuck-on spots, 3M says to soften "bug splatter, bird droppings and tree sap by soaking them for several minutes with very hot, soapy water," and warns, "Do not use rough scrubbing or abrasive tools, as this will scratch the film." For more on why droppings cannot wait, see how bird droppings damage car paint over time.

 

Products to avoid, per Avery Dennison:

 

  1. Any product that contains petroleum distillates

  2. Aromatic solvents "such as acetone, M.E.K., toluene, paint thinner or lacquer thinner"

  3. Chemicals or detergents outside the pH 5 to 9 range

 

Drying helps too. 3M and Avery both suggest a silicone squeegee followed by a microfiber cloth to reduce water spotting, and XPEL says to dry COLOR PPF "after each wash." This post on what spot-free rinse is and why it matters covers the rinse side.

 

FAQ

 

Can you take a wrapped car through a touchless car wash?

 

3M says touchless washes are the best for graphic care, and Avery Dennison says a brushless automatic wash with just spray is acceptable. Wait out the cure time first.

 

How long after a wrap or PPF install can I wash my car?

 

XPEL says 48 hours for ULTIMATE PLUS, ULTIMATE FUSION and STEALTH and 72 hours for COLOR PPF. Avery Dennison says 48 hours for Supreme Wrap, and 3M says the first week, longer in very cold weather.

 

What psi is safe for a vinyl wrap?

 

Avery Dennison says below 1200 psi, and 3M says below 2000 psi. Use your own film maker's number.

 

Can I get the wax option on a wrapped car?

 

Avery Dennison says to skip the wax options at the car wash, and 3M recommends no wax or similar coatings on vehicle graphics.

 

Do brush car washes damage wraps?

 

3M says brush washes may cause dulling, scratching and lifting around the edges, and Avery Dennison says brushes may scratch the vinyl and catch and lift the edges.

 

Can you pressure wash paint protection film?

 

Yes, with care. XPEL says to keep high-pressure water away from film edges and to stay 3 feet away from COLOR PPF.

 

Touch-Free Washes at Three Rivers Car Wash

 

Three Rivers Car Wash runs touch-free automatic washes, the type 3M calls the best for graphic care, open 24/7 in Canonsburg, Washington and Meadowlands. Its site says the touch-free process is "designed to be gentle on all paint types, clear coats, and specialty finishes." If you want to skip the add-ons on a wrapped car, the Express package covers the Foam Action Presoak, High Pressure Wash and Spot Free Rinse. Check your film maker's limits first, then stop by the Meadowlands location or the Maiden Street location in Washington.

 

Visit Three Rivers Car Wash or call (724) 222-6580 today. Contact us for more information.


Three Rivers Car Wash

 
 
 

Comments


bottom of page